MikroTik - Search

stef84

Do you know if is planned an hardware Wifi6 (similar hap ax2 or hap ax3) but wallmount like cAP AC?

stef84

Hello.
It’s possibile in SWitchOS and in This CSS106-5G-1S config the port Priority and path cost like RouterOS in the bridge section?
Thanks

stef84

Thank you very mutch.

I've change only mark-packet and now work

But I can not tell if the rest of the traffic is regular and if the only traffic of TCP 10333 is limited

Thanks

stef84

thanks friend for the help.... i've use this rule, but it's not work: add action=mark-routing chain=prerouting new-routing-mark=service passthrough=\ no protocol=tcp src-address=192.168.1.41 src-port=10333 add comment=NAME limit-at=256k/8M max-limit=256k/8M name=NAME \ packet-marks=service queue=pcq...

stef84

Hello... i've a question

I've an host 192.168.1.41 in my LAN. I need limit bandwith 256k/3M on this host only for service use port 10333 TCP. I've creating a prerouting-mark in magle for this port, but the queue don't work.

can you help me? Thanks

stef84

Thank friends for the replay. I've two connection, the older is in a ether5-wan, from a 30/3 wisp connection and is here only for backup, but now not work. I'm actually use a VDSL ( ~ 90/20 ) from VLAN20 and the 2011 have a pppoe-client. This is my configuration. I think the problem is the hardware,...

stef84

Hello. I use my RB2011 with VLAN service. I've a problem with VLAN and i don't understed if my configration is correct, because i've an increase of RB CPU UP 70% with high traffic (~100Mbps with speedtest) and use the RB CPU rather than Switch CPU. The SwitchCPU setting in VLAN mode, it must be FALL...

stef84

Hello.

After update 6.43, I don't connect in winbox remotly from wan with winbox, i connect only in LAN... With 6.42.7 i connect perflectly from remote.

Any solution?

stef84

Hello.

With 6.43 i don't connect remote from wan with winbox or 80 port. I enter only from LAN.

were is the solution?

Thanks

stef84

Hello... I've a Mikrotik cAP_AC used for AP in my home... I've an issue... Initially i accused slowly bandith in WLAN 2,4 Ghz and the 5Ghz radio dosn't work ( any device do'nt connect at this), but this is not a problem in this moment. If I reboot the rb, initially the bandwith is very good 30/3Mbps...

stef84

Hello everybody. In my country they are installing FTTC fiber optic from TIM and I would like to foresee an eventual upgrade. I am looking for a VDSL2 modem to connect to my Mikrotik devices in my network and I have seen the Proscend 180-T product that I could connect to my RB2011's SFP port. do yo...

stef84

Hello everybody. In my country they are installing FTTC fiber optic from TIM and I would like to foresee an eventual upgrade. I am looking for a VDSL2 modem to connect to my Mikrotik devices in my network and I have seen the Proscend 180-T product that I could connect to my RB2011's SFP port. do you...

stef84

Thanks for replay and for the help.

I've disable ALL info memory logging, but in this case I've stop to logging ALL Info...

I don't understand if is the correct way....

Thank you.

stef84

Ops, sorry for the error... Sorry, I thought the post was inherent in the "general" category rather than "script" this is my script: /system script add name=fetch_new owner=admin policy=\ ftp,reboot,read,write,policy,test,password,sniff,sensitive,romon source="/\ tool fetch ...

stef84

Can anyone help me?
Thanks in advance, sorry for my bad english.

stef84

Hello everybody

I have a script to check and possibly update my freedns account every 5 minutes.

I would like the valuenot to be logged memory info fetch:file "update... etc etc".

I would not have this value in LOG, everything else... It's possible?

Thanks

stef84

Thank you so mutch scambell for the replay and for the help. I am a self-taught beginner. I am looking at the config and it seems you shouldn't need all these VLAN's and bridges - in Bridge<->Station-Bridge mode the QRT's will pass all the VLAN's directly (i.e transparent bridge.) to your RB2011's. ...

stef84

Hello. I think i've solved my problem .

I've set Framer Policy = exact size and Frammer Limit=4000

I Test IT, but in this mode i'dont have disconnect.

Thanks

stef84

大家好…我意识到一个桥有两个abotation at 800mt with two QRT. In this bridge, i've create foru VLAN, for transport it more device. One VLAN is for LAN, one VLAN is for GUEST, one VLAN is for transfer HDMI signal with HDBitT module LKV383 and one VLAN is create for the future uti...

stef84

Thankyou so mutch.

Have yet to find that IRL on any cities, you're really lucky! how much does that QRT AC at 80MHz pass?

Sorry, i don't understand...

I've Set QRT Radio in N chanel, but I receive this message:

failure: this device can not do spectral scan

Thanks

stef84

其实我用电桥和两个Mikrotik QRT雷竞技网站extend my LAN at 800mt and a bridge with two Sextant for my work office. at 500mt With QRT i use 80Mhz channel and i've a good throughput... In this radio i use 4 VLAN, actually one for trasfer H264 HD video signal with HDBit module at 22Mbps, one fo...

stef84

Thanks for replay. No, I don't have do a spectrum scan in a pleace now. I'm considering whether to make this investment to bring Fiber to my office and resell bandwidth to some customers. I would like to become Wisp, but first to evaluate if I could get enough bandwidth. Anyway, it was a curiosity I...

stef84

Hello everybody. I've a question. I would like to know if this transfer is possible in this mode, for transfer Fiber Optic Connection 300Mbps at 5Km. I wold to use: 3) - Mikrotik SFP Module 2) - RB 922UAGS 2) - Mikrotik mANT 30 + sma cable 1) - RB 3011 I would like to use RB3011 to connect PPPOE cli...

stef84

Nothing.... The campsman not work... i see the device, see the ssid but wen i try to connect, my client not connect to it... I don't understend were is the problem. For the moment, i set all the access Point with old configuration, (bridge Ethernet+Wi-Fi) but the system don't respond very well. I've...

stef84

Thank you very muth for the explanation and sorry for my bad english. Tomorrow i go in the hotel for re-setting the device with capsman. I planing this situation, and use two chanel ( 2422 and 2462) for all the device. What do you think? I don't now if is better use "auto" channel for all ...

stef84

Hello friends for help me and replay. I test the capsman in my house. I've a RB2011L to set the capsman and i connect it an cAP Lite for test. The system is work very fine. I've set the access list in caps-man ( Rb2011), It's ok this setting rule? In the Hotel, you can recommend me to use the same c...

stef84

Thanks for the replay friend. Sorry for my question, but i'm only a pratician and sorry for the stupid question. I would love to learn so much. I use rb750 to route all traffic. It's possibile to set CapsMan in the rb750 for control all AP? I's possibile to have a sample of the rule to controll low ...

stef84

Hello everybody. I've install 14 Access Point ( Mikrotik cAP Lite) in a Hotel. All the access point is connected with lan in a switch and is in the same network, and all have the same SSID and WPA2-EAS. I've planing the setting of the access point radio not disturb the one with the other, and use th...

stef84

Thanks for replay.... I've try to change route 192.168.35.0 255.255.255.0 but don't work. I'm not ping 192.168.35.105 from rb2011. If is necessary to send all traffic of iphone VPN by my router is not problem, but my necessity is only to view and ping my all local machine in 192.168.1.0/24 from my i...

stef84

Hello Everybody I've setup a OVPN tun on my Router RB2011 for connect my iPhone in my LAN from remote. The connection is stabilished, but i don't ping my smartphone from the rb2011. My LAN is in 192.168.1.0/24, the VPN Tun is in 192.168.35.0/24 my iPhone client have internal adress 192.168.35.101, e...

stef84

I've view a StationBox XL by RF Elements and i'm interesting. I view the datasheet and the spectrum of the panel is interessant. Is compatible with board of RB911G-5HPacD 802.11ac. https://s28.postimg.org/gjqapc0b1/stationbox.png Otherwise, this is the datasheet spetrum of Dynadish. https://s28.post...

stef84

Very thanks for replay. The solution of repleace only the board is not good for me, because if buy two new RB911ac i sell my old sextant. OK, is necessary to buy an antenna with dual polarization. If i decide to buy NetBox5 RB911G-5HPacD-NB 802.11ac 866Mbps, and buy an antenna with dual polarization...

stef84

Thanks for replay and help.

Honestly, i don't like Dynafish, because is very bigger and cumbersome.

If i buy NetBox5 RB911G-5HPacD-NB 802.11ac 866Mbps + grid antenna 23dBi ?

Thanks

stef84

Hello everybody. I nedd to replease my actual p2p bridge compose to two SEXTANT RB911G-5HPnD ( 1.5Km distance), for improve performance and trouthout. I'm uncertain to buy two product. Bridge with 2 RouterBOARD SXTG 5HPacD or bridge with 2 RB911G-5HPacD-QRT The SXT (16dBi antenna) is more cheaper th...

stef84

Thanks for replay.

I don't understand. I must add a rule in my mikrotik router (192.168.1.1) or in my Openwrt device (192.168.1.11)?

stef84

Hello. I've a question. I've a VPS and tunneling it with OpenVPN. For connect to the VPS in VPN i use an OpenWRT hardware, connected to my local lan and any machine in my LAN is direct connect to the VPS. For it, i've use a simple routes in myt router (RB2011) to route the LAN to TUN. /ip route add ...

stef84

Hello.

I've set a sript for no-ip dyndns update, but it write in log any 5-10 minutes :fetch: file "dyndns.checkip.html" downloaded.

It's possible to STOP de logging in memeory for this event and don't fill the memory?

Thanks

stef84

Is it possible, but i use the internet conneciton in two house and is necessary use the RB2011 for my NAT and more rule.
Anyway, i set directly the ETH1 and ETH2 of RB2011 simply in switch mode and don't have any drop of performance in this metod.

stef84

Ciao Alessio :D NO, My WISP is a Local WISP (not Eolo NGI), but offer me 30/3 Mbps connection with Cambium ePMP1000 (Force 200). Originally I use a RB2011 in Bridge with a Pirelli ADSL2+ (Telecom) for pppoe an a adsl connection. But because i've 48dB attenuation in my line and i've only 4Mbps ADSL ...

stef84

OK, thanks... I think the problem is the time in the day i do the speedtest.

I test now the internet connection in the PC near the AP and effectly the test is the same, sorry.

Anyway in NStreame i've increase more than NV2.

Thanks very mutch.

stef84

Thanks for replay.

In NStreame i've increase more the FTP transfer. I've arrive at ~9MB/s, but the internet connection non increase.

stef84

Hello everybody. I'm Italian and sorry for my poor english. I've a problem on my 2Km ( no ostacle, i view the other side ) Bridge P2P realized with 2 RB911 Sextant. In site A (AP) i've a WISP Internet connection can offer me 30/3 Mbps. In site B (Station) arrived me only ~10/1 Mbps internet connecti...

Search found 42 matches