RB2011, v7.7 is unstable :-/ v7.6 was OK all the time...

hAP lite: after upgrade from 6.45.1 to 6.46webproxy doesn't work

Is there something wrong with traffic counter?

(RB2011 with RoS v6.34)

6.29rc14 With enabled FastTrack increased connections with last-ack state, is that normal? /ip firewall filter add action=fasttrack-connection chain=forward comment=\ "fasttrack established+related" connection-state=established,related add chain=forward comment="enable established+rel...

I run it on RB2011UAS-2HnD and it works.

visalink:如何/你的火wall rule/rules look like?

or

Did you use CCR device? FastTrack will work properly on CCR devices starting from 6.29rc14 version.

FastTrack

great improvement, thanks... just tested a bit

- sector writes start to increase by 1 - 2 every second untill you reboot router.

1) Close Firewall window and then close Winbox.
2) Run Winbox.
3) What about sector writes? I don't see any increasing now...

ROS 6.28, RB2011UAS-2HnD

try this

1) Tools -> RoMON, check ENABLE, click OK

2) Tools -> RoMON, uncheck ENABLE, click OK

CPU usage will be 100%, you must enable it again.

You should do more practical tests before you release new RoS version, Mikrotik.

I will use v6.5, v6.6 isn't good choice for me. :/ Thanks for your comments, guys.

Check on your Mikrotik Web Proxy and if enabled, check access policy.

Thanks for Your answer. I will send supout.rif to support. And yes, I did connect to Winbox. Everything else worked perfect. I tried to scan some ports from other network and without firewall rules they were opened, not filtered.

Hi guys,

I just update RoS 6.2 to RoS 6.3 and after update I lost all my firewall rules (IP->Firewall->Filter rules), so my RB becomes an open proxy (WebProxy was activated without any access policy - my fault). I added rules manually and I'll see what happens after next reboot.

I just want to report that 6to4 tunnel is now working!It works perfectly with ROS v5.xx and now with v6rc11 it works too. Previous rc versions didn't work at all with my RB2011UAS-2HnD-IN...

Your hardware is great, guys. But there is a lot to do with your software.

只是让你知道,在更新a RB2011L-IN and a RB2011UAS-2Hnd the activity led of every port is blinking.

cool stuff

Since I do decompiling as a hobby, I grabbed the "cracked" 5.18 ISO and did a quick analysis on what the crack changed.
Conclusion: DON'T USE !

Good job, norbyte!

Zdravím Čechy a Slováky :D (Greetings to Czechs and Slovaks) Before update with RoS v5.22 -> 6to4 tunnel worked great - ping to IPv6 gateway was OK. ros522.png After update to RoS v6.05rc -> 6to4 tunnel didn't work. Gateway was unreachable. Nothing helped (re-setting interface, deleting/adding IPs, ...

After upgrade to 6.0rc5 (from 5.22) my 6to4 tunnel stops working anymore - HE.net's IPv6 gateway was unreachable. I downgrade back to 5.22 and it works like a charm!

So... thanks for your answer anyway.

Hi guys, I want to get maximum performance from my new RB2011UAS-2HnD-IN. I've got a gigabit switch which supports Jumbo frames (9kB), my network cards supports Jumbo frames too (2kB to 9kB MTU). How can I change interface configuration to get maximum performace? Switch is connected to ether1: http:...

Hi guys,

can I change VIA header in web proxy? I've got some linux servers with SQUID and it is easy. But here is no config file to edit.

for exampleThanks!