You're quite correct. When running those tests, I had 1 CPU hitting 100%. When running iperf3 with the -P 4 parameter, I get pretty close to the 2.5Gbps target and the CPU (in total) goes to about 75% Your explanation does make sense though, so thanks for that. In practice, I doubt very much I'll re...

Hi. I've an RB4011 connected to an Aruba 6300M by means of an spf+ DAC negotiating at 10Gbps. Over the weekend, I decided to put some 2.5Gbps NICs into my servers in order to make use of the extra speeds the ports on the 6300M provide. However, I noticed when performing an iperf3 test across VLANs, ...

Same Issue here, i've removed all lacp bonding interfaces from the bridge, after that, the switch worked fine, so i downgraded to the last 6.47.x I've also tried a factory reset and reconfiguration with a export backup .... same issue. Ahh. I have 3 LACP bonds on mine. I may well be having the same...

On my CRS326-24G-2S+ after updating I no longer have any interfaces nor will the device reboot cleanly. This is the output from terminal: [admin@CRS326] > /interface [admin@CRS326] /interface> print Flags: D - dynamic, X - disabled, R - running, S - slave # NAME TYPE ACTUAL-MTU L2MTU [admin@CRS326] ...

添加每个vlan标记做了调节的桥梁k. Thanks very much for that.

Thanks. So, I did try that - I set a port on the bridge to untagged VLAN4 and then enabled vlan-filtering on the bridge. Plugging in a client to that port and I do not get an IP from the DHCP server on that VLAN. I may be missing something else here. Would I need to also add the VLAN interfaces to t...

Hi all, So i'm attempting to migrate a config from an RB3011 to an RB4011. Everything's going fine, aside from setting PVIDs on the ports. On the RB3011, the switch ports look like this: [admin@RB3011] /interface ethernet switch port> print Flags: I - invalid # NAME SWITCH VLAN-MODE VLAN-HEADER DEFA...

Hi all, Not sure what's going on here. I have CAPsMAN up and running. Has been for some time. Recently, I decided to go ahead and add a guest SSID, but for some reason, I cannot seem to get it provisioned. Here's my config # feb/20/2019 03:46:16 by RouterOS 6.43.12 # software id = DRFA-DX22 # # mode...

Hi, I've been assigned a group of static IPs from my ISP and I'm trying to get them to work with my RB3011. So, the setup is this. I have a Draytek Vigor 2860 currently acting as a bridge (PPPoE passthrough) serving my VDSL connection to the RB3011. The RB3011 has a PPPoE client assigned to ether1, ...

Thanks for the reply.
So if I read that correctly, I can't have a trunk/more than 1 vlan on ether1?

I'm having trouble getting my hAPac Lite to work with vlans. Here's the switch config: # may/27/2018 15:25:51 by RouterOS 6.42.3 # model = RouterBOARD 952Ui-5ac2nD /interface ethernet switch vlan add ports=ether1,ether5,switch1-cpu switch=switch1 vlan-id=1 add ports=ether1,ether2,ether3,ether4,switc...

Hi all, I'm struggling to get the best speeds possible from my home CAPsMAN setup. First, an overview of my infrastructure: I have 2 wireless devices, connected to an RB3011 which is acting as the CAPsMAN server. Those devices are:- RouterBOARD 962UiGS-5HacT2HnT RouterBOARD wAP G-5HacT2HnD I also ha...

你好,我刚刚更新了我的老RB450G 6.41order to test it before upgrading my RB3011 & CRS326. I'm having some issues with VLANs. The RB450 is connected direct to the RB3011, which hosts several VLANs. The RB450's config is completely blank, except for the following: [admin@RB450G] /in...

Hi, I've just gotten a CRS326-24G-2S+ for my homelab. I have some previous experience with RouterOS on an older RB450G, but it's been a while. Now, I'm not a network engineer, I'm a server guy, so I'm probably missing something obvious. Reading up on the forums you need v6.41 to enable hardware-offl...