MikroTik - Search

wtm

Can you please bring out some type of swivel bracketing for the 60 ghz wAP (AP and CPE) line. The current slide in bracket and pipe clamp do not allow any vertical alignment adjustments to the radio. This is especially needed since the 60 Ghz radios are really tight line of site adjustments.

wtm

Could this be a problem with the particular version of the SSH software ? Does Mikrotik need to update the version of SSH that they have in the router OS ?
What version of SSH is currently being used ?

wtm

Seem to be having problems with the software downloads. Some files such as the Router OS show only 11kb (when they should be 11 Mb). Netinstall runs but states that the file only has 0kb in it.
Seems to be both on the Long Term and Stable branches.

wtm

So what firmware do we need to install on what routers to prevent this ?

wtm

No, what is happening, is that the big trucks on the highway have WiFi transponders in them, for use by the "weighing stations". So they will latch on to my hotspot, get an IP address, and then do nothing, as they do not get the proper handshake that the weigh station gives them. They will...

wtm

Need to block massive amounts of MAC codes of the local truck transponders (Ezurio), that keep using IP addresses on my hotspot. How can I accomplish this?

wtm

We upgraded all our routers last night. Immediately lost the webserver on one, and today, they lost access to the webserver on another. A reboot brought access back up on them. Scramble to log back in to all, and turn on SSH to make sure we have a way to get back in them. Looks like there may be a p...

wtm

Really stupid and ineffecient to have AC to DC, and then DC back to AC again. Just put in a DC jack to begin with. I understand that the board runs on 24 volt DC anyway.

wtm

Do you have the part number from Mouser?
Is the + side of the connector in the front or back?

Thanks,
Wayne

Still NO excuse for Mikrotik to not have a DC input on those, considering the cost of them.

wtm

So as we are upgrading to higher speeds (CCR-1036 for 10 gig) , we started buying higher grade routers. To now find out that they don't have DC power input capabilities ? Dear Mikrotik, Not everyone has AC electric to ALL their Internet sites, and there are some of us that use DC powering as "B...

wtm

Bump ........
Is there anything new on this? As IPV4 addresses get in shorter demand?

wtm

Would like to see a Radius tester available for the "Tools section". Something along the lines of Radtest, so you can see that the external radius server is actually getting something from the Mikrotik router, and if not what the problem may be to fix it. Currently there is not enough info...

wtm

我们可以得到类似于routerO“Radtest”S, so we can test that the router is capable of actually getting to the radius server? All that I can seem to get from the current logs is an error message that the router can't contact the Radius server. It would be nice to have something ...

wtm

In respect to the KRACK situation, and the need to use "https" as much as possible, it would really be nice if the Router OS (and routers) come with a "self-signed https certificate" like most of the other vendors equipment does! This would allow immediate use of HTTPS as the log...

wtm

Well, the biggest gathering of WISP's and IT techs just finished this week in Las Vegas. Lots of vendors, many really great classes on industry related topics. Just one thing missing........................MIKROTIK ! Why can't Mikrotik be at this event? It is the largest gathering in the USA of peop...

wtm

Thanks All,

wtm

I was wondering, is there anyway to run the Dude on a Linux (centos 6.9 server), as a "standalone" server program? I understand that you have to have RouterOS x86 to run it, but my concern is that we are using the server for other programs and services, and I don't want to run RouterOS on ...

wtm

Great !
thanks,
Wayne

wtm

Why is it that the first thing that pops up when you login is the "Quick" programming wizard tab? Anyway to disable this, and have it go to the "Interface" tab instead. We have employees that are not real technical that have to use the routers to access AP's and do maintenance on...

wtm

I can see where the branding package would allow me to put the Company name and contact number on the router, BUT, what about having a line that shows the "Identity" of the router on the login page ?

wtm

Not what I am looking for ! Login page, already says to contact the administrator is you view this! Needs to display a company name and contact number to provide that on the login page. Also the "Identity" of the router needs to be displayed, BEFORE you should have to login to look for tha...

wtm

I know that many before me have requested something like this (As that is what I am seeing on my searches). BUT, so far it is only available by getting the "Brandy Maker", which I am told is only available to distributors, and resellers. What is truly needed is for the main login page to s...

wtm

On the WAN side you will usually have another /30 which you get from the provider just to connect the two routers. Configure that. How's THAT going to give me divided subnet on the /23 on my LAN side ? What I want to do is to be able to take some Public IP's through the site routers, where my netwo...

wtm

Do I just program the router WAN with the /24, and then the LAN port with a /30 ?

Well, THAT didn't work ? Anyone have any suggestions?

wtm

Thanks guys !
Wayne

wtm

I have gone through the web looking at ways to do subnets for my WISP to provide customers their own IP blocks. So far all I can find information about is how mathematically subnets are divided? Not how they are "physically" programmed into a router to do it ! What I would like to do, is s...

wtm

Thanks,
Wayne

wtm

After going over the Wiki on setting up a 1:1 NAT, I still have a few questions (for you router guru's out there), and want to make sure I understand the exact programming to make this work correctly? First, on how the router (example) is setup: WAN = 123.1.1.10/24 (Ether 13) Lan 1 = 10.1.1.0/24 (Et...

wtm

If you are going to work on putting the "Dude" on any standalone server, I would rather you put the effort into doing it on a "Linux" server !

wtm

This may open up a whole new look at what is needed for CALEA compliance? http://www.usnews.com/news/articles/2015/11/30/internet-provider-gagged-for-decade-reveals-what-fbi-wanted-without-warrant I know that the Mikrotik routers have a CALEA option available on them, but it might be worth a second ...

wtm

NO, we just log into the router via them. It would just be nice when you do so, to know where that router is located, instead of what firmware version it currently has ? An "Identity" line on the webfig login page would be helpful !

wtm

It would really help, if on the "main login page" of the router, that a "location" line could be put in. Also at the top of each page next to the "Webfig". This would help identifying the exact router that you have logged into. When we are doing some maintenance, we som...

wtm

Request for a new hardware version to the CCR line. A router that is top of the line like the CCR-1036, but is small as in the number of physical ports it has on it, and can be used mainly as a "Head End" MAIN router to the network from a fiber connection. It would need maybe 2 WAN or Fibe...

wtm

Thanks for the reply. I was able to get the proper programming for both Eth0 and Eth1. We are doing Static's on all the connection, so don't use DHCP. I am only able to get a connection from Eth2 through to Eth1, IF, I setup a Masquerade on the NAT. Otherwise, not able to get in or out on it. There ...

wtm

Have a RB1100AH router, currently have a /25 Public IP block available on the WAN side. (example: 205.123.123.128-205.123.123.255) I would like to sub divide that /25 into a /29 Public IP block for a School. (205.123.123.208 - 205.123.123.225 /29) Can I just assign that address block to a LAN port? ...

wtm

Fixed the problem............It needed a LONGER CAT 5 jumper cable. Then it would connect as 1 gig.

But unable to turn on the Flow Control on that port ?

wtm

What, no one on this forum has an idea on solving this ?

wtm

We have recently upgraded our backhaul network, and I am in the process of making sure everything connects at 1 gig. We upgraded the firmware on our existing RB1100AH unit to 6.27 , and port 13 (Internet connection) will still not connect at 1 gig , although it shows that it is advertising, and has ...

wtm

Thanks!

wtm

Where can we download version 6.27 software for several of our PPC and Mipsbe devices?

wtm

Looking for pros and cons on the RB922 units, looking to replace some UBNT Rockets with an AC device, and the RB922 seems to be able to do that. Just need to see if they work as long distance back haul links. (25+ miles)
And what type of throughput I can expect on them?
thanks,
Wayne

wtm

I am not a consumer, I am a WISP operator !

wtm

Request that somehow that we could put in an "Emergency contact number" on the Main Router "Splash" page.

This would allow people to contact the router owner, rather than try to play with the unit to find out who owns it, etc !!!

wtm

我不想要一个“热点”服务器,Mikrotik意志雷竞技网站already do that !!! What I want is the Mikrotik that can be setup to do "Reverts" when the customer is NOT authorized. Just setup a "Common" IP Pool in the router IP pools section, and call it "Expired". Then ...

wtm

We bought Radius Manager, and although it works well, it does not do all the accounting that our company needs. If also does not allow more breakdown on the sale items, and such. We could not get it to do what we needed on the sales and accounting end. WHMCS software worked well on the accounting/sa...

wtm

Haven't seen or heard anything back yet !!!

wtm

Only if the Accounting software is setup to do it. Problem is that most are NOT, and they only will do a "User" entry, of "User" deleted for Authentication in the Radius Server. There seems to be nothing in between for most software. Radius Manager is so far the only one I have s...

wtm

When using the Radius Client/PPPoE Server in the router unit. Is it possible to include a "Revert" to an "Expired" named IP pool listed in the router OS IP pools. When the Radius Server advises the Router that the customer is "Non-Authorized", the Router would direct th...

wtm

Well, it is working fine !!!

Thank you very much !!!!!

Doesn't need the firewall rules, yet (ha ha) !

一个设备似乎是噢n problem, as everything else is working fine on the network.

Again, Thank you,
Wayne

wtm

Do I need to do any forwarding rules on this? Remotely I can ping an address of a device on the LAN OK now using the /25 subset, but unable to access it by http port(80). There isn't any firewall rules in place, (that I can find), so I do not see why I can't access the device remotely. I am able to ...

wtm

I was given a full /25 set of public Ip's from my backhaul provider. Normally I know how to program a router to use a SNAT and DNAT for a single Ip to Private IP's for the end users, but I can't seem to get the programming on this one to provide the FULL /25 Public Ip subset onto the LAN side of the...

wtm

Does it have to be a Microtik router machine, or can it be a standard computer unit or server, which is what I want to do !

Will that main User manager then talk to all the other router units and manage them from that main unit ?

wtm

I don't know if there is anything already available to do this , but I have been unable to see anything on the website or forum. It would be nice is User Manager was available as a standalone central server. And it could communicate with other Microtik routers. Essentially have one central location ...

Search found 53 matches