MikroTik - Search

Polky

Sorry, bad english. I thought 1 connection in Btest. I'm always testing 1 connection. Zero traffic: I think other AP clients carry a small amount of data. Previously, I was not able to make 100 Mbits for 1 connection in the NV2 protocol with so many clients. https://t18.pixhost.org/thumbs/98/6711328...

Polky

I'm very glad that one client will not kill the entire AP.
AP上的新变化是非常好的,但当the last rc version I upload to the client, it behaves very weird about CCQ and ping, even though I think it has a very good signal and CCQ.

Polky

@uldis I started uploading rc49 to client units. But I have terrible results. Ping 5,5,450,10,730 ... etc . It's quiet for a while, and CCQ falls, and RATE to 6 Mbits, and it's up again. Test for Omnitik a / n and RB711 client. I get the same results with SXT SA5ac and SXTsq client. As soon as the c...

Polky

@uldis Uploaded last rc46 i rc49 and watching great improvement. Linking to 1 thread is far better. Previously, I had to use AP 802.11 for that. Now Omnitik AC, 19 clients, 20/40 Ce, 2ms, dynamic 75 (no client has AC) .. 1 thread will make 110 Mbits, which was previously impossible. Of course, there...

Polky

Hi I have the same problem on RB2011iL, several ports in the bridge. The client can not access until you clear the ARP table the MAC. RB at no extra rules.
Some idea ?
THX

Polky

Hello, I have a main gateway to the Supermicro X8ST3-FO with XEON (2x Intel ® 82574L Gigabit Ethernet Controllers). - RouterOS 6.10 Intermittently stops traffic across the network card. I joined other cards, but it's the same. It helps disable and enable Ethernet or reboot the server. Please help. I...

Polky

Hi, I have a main gateway built on Xeon with Supermicro board. Version 6.10, and use DNS for about 1000 clients. However, lately very long to translate addresses before DNS. DNS settings: Allow Remote Requests on 2 local server with BIND Max UDP Packet Size: 8192 Cache Size: 8192 DNS blocked from th...

Polky

Hi, after upgrade to 6.9 from 6.8rc1, ceased to function gateway with routing mark.
Unable to select routing mark! - Is empty.
Donwgrade back 6.8rc1 works.

THX

Polky

Always the same shit, AP stops transmitting data at any time! Clients are angry.
They do stupid things just type quote changelog: lcd - changed gamma, which gives greater contrast
Super, NV2 does not work, but most that I can adjust the contrast.

Polky

Hi, I have the same problem. When using NV2 time to time to become! I have to turn off and turn on the wlan AP or AP reboot. It happens from the beginning NV2. Clients are connected to the AP, but passed through not pass anything. I have tried to AP 5.21 and 5.21 on the client, the latest firmware a...

Polky

I had big problems with NV2, after upgrade to 5.21rc1 links runs great!
Thanks MT team!

Polky

a nano station as an AP ?

Nano as AP - only on the test.

I do not like UBNT products, but unfortunately begins to confirm that they are in a better wireless.

Polky

I also have many mikrotik only AP and clients. Here I wanted to demonstrate the difference between Mikrotik and UBNT already in common 802.11. It is true that all are in noisy environments. But UBNT holds several days. Mikrotik only a few hours, sometimes just minutes. And also talking about NV2 and...

Polky

On the pictures I want to show how the connection holds UBNT far better than Mikrotik. AP Mikrotik and UBNT several clients and one mikrotik. UBNT AP and several clients Mikrotik and UBNT one. UBNT always keeping a link a few days, mikrotik just a few hours! I do not know what to think about when wo...

Polky

Now that's funny. NV2 nothing. Migrate to the Airmax UBNT. Clients will not wait

Could anyone please remind me what we're specifically talking about?

Talking about this
Fortunately, I have set the client only 1 frequency AP. (scan list) To recconect took the least time.

Polky

Now that's funny. NV2 nothing. Migrate to the Airmax UBNT. Clients will not wait Still, I upgraded to 5.20. And I must say that it is Nstreme NV2 and more stable! Although nothing in the changelog. In some places, the stability improved. In some places, has not improved. Anyway, it's a step forward...

Polky

Now that's funny. NV2 nothing. Migrate to the Airmax UBNT. Clients will not wait

Polky

I would prefer to test the functionality. NV2 is useless in most cases. UBNT beat MK, both in response and in functionality.

Polky

Yes, all clients have the latest firmware. On some sites NV2 works. But most did not. I now have a new AP + RB711GA big Airmax sector. Approximately 13 clients. And every day the AP problem. AP stops transmitting data through. I have to reboot or turn off and turn on the interface.

Polky

Hi I have the same problem in different routerboard. NV2 is useless. AP stops traffic. Other AP constantly doing reconnect.

clients 5.17 , AP 5.17 .

Polky

Hi, I have the same problem. NV2 is constantly disconnects. I also use shielded boxes and quality dish. There I discovered another problem with the NV2, link is attached, but do not pass any data. AP Bridge (bridge= eth1 + wlan) ----- station (static routing) - link is active, but occasionally pass ...

Polky

Hi All, I Upgraded a 433 to ver 5.13 running a Dbii pro50 wireless card. pings to client cpes have improved dramatically across the board. Has anybody else noticed this? Is this an actual improvement or just a change in the way the ping time is calculated and reported? Ver 5.11 pings average 3 - 8m...

Polky

I'm reporting the same problem! Of the 10 pieces 5 pieces KO. Today I installed the antenna 3 times. He was always a good time signal and after a while -80. And the last unit of this error reported after 2 hours.

Polky

Hi, I know the answer from support? Basically, all connections with NV2 behave worse than the Nstreme, if used only a single connection. It's bad, because all clients use the speed tests that use a 1 connection.

THX

Polky

Hi, also test the NV2 in version 5.9 and I see great improvement. As for stability, speed and response. When using longer NV2 does not reduce the signal. Which RouterBOARD you have a problem with Ethernet? P.S. The only thing that bothers me is the speed when downloading only 1 TCP connection. Most ...

Polky

I am also waiting since June for RB750UP. I need to rebuilding the AP. Unfortunately, after a while begins to fall again the snow, so I'll have to take solder and do something myself. I think neither will there be this year.

Polky

Abnormal Traffic will no longer appear on the upgrade version 5.4. Thank you!

Polky

Info about NV2 Problems with wireless I describe here. I wanted to use NV2, but unfortunately the clients are often disconnected with the following message CONTROL FRAME TIMEOUT. Disconnecting lasted several minutes. At 802.11, or NST runs fine. The signals are so good, I think, when running standar...

Polky

你好,我确定我有同样的问题在5 GHzband. The standard 802.11 or NST works without problems. I was expecting great strength NV2 using P2MP. When using NV2 frequently appears in the log Lost Connection Control frame timeout and the Lost connection, medium-access timeout. I used differe...

Polky

yes WLAN1-5 AP-Bridge and AP are all in BRIDGE1. For example, the user is connected to WLAN2. It is RouterBOARD STATION BRIDGE mode as soon to be 3 Mbps download from the Internet and will show the same data stream on ETH3, as shown in the picture. As if poorly directed. I tried to turn all RSTP but...

Polky

Hi, thanks for the reply. I attach a sample problem STATION BRIDGE mode. Example: wlan1 - WAN eth3, wlan2, wlan3, wlan4, wlan5 - Bridge Please look at ETH3! TX traffic, which according to the TORCH coming from the direction of wlan1, wlan2, wlan3, wlan4, wlan5 (by IP). The abnormal traffic only come...

Polky

Hi, I came across a problem with the mode STATION BRIDGE version 5.x. Example: (5.2 version at all routerboard) RB433: EHT3 - WAN Bridge: eth1, wlan1 (AP) wlan2 (AP) wlan3 (AP) If you set up for a client (connected to the WLAN AP 1-3) STATION BRIDGE mode, it detects to eth1 (client) abnormal traffic...

Polky

Hey, the RC1 is still not functional bridge or WDS? (with NV2) I tried AP brigde ---> pseudobridge station, but failed. pseudobridge isn't working with Nv2. Use station-wds on the client side. Thanks, I have RB411AH (Nstreme) (5RC1) ----> RB600 (with RB604) (5RC1) RB600 has 5 miniPCI. 1st Station -...

Polky

Hey, the RC1 is still not functional bridge or WDS? (with NV2)

I tried AP brigde ---> pseudobridge station, but failed.

Polky

Hi, please where can I download the RC1?
Thank you, also tests P2MP.

Search found 35 matches

Re: Significant improvement for wireless Nv2 PtMP

Re: Significant improvement for wireless Nv2 PtMP

Re: Significant improvement for wireless Nv2 PtMP

Re: Significant improvement for wireless Nv2 PtMP

Re: HELP !!!!! How to protect Router automatic Mac generate

Supermicro X8ST3-F-O stops traffic

DNS - very slow

Re: 6.9 released!

Re: 5.24 released!

Re: NV2 + 5.20 some CPE unreachable (??)

Re: NV2 disconnect problem

Re: UBNT vs. Mikrotik - connection stability

Re: UBNT vs. Mikrotik - connection stability

UBNT vs. Mikrotik - connection stability

Re: v5.20 released

Re: v5.20 released

Re: v5.20 released

再保险:ROS SXT和ubnt与延迟

Re: Connection looks good but no data passing thru???! v5.13

Re: Connection looks good but no data passing thru???! v5.13

Re: NV2 disconnect problem

Re: v5.13 released

Re: NEW RB711

Re: Only from 10 to 25Mbit/s per one connetcion in NV2

Re: V5.9 Nv2 performance improvement

Re: RB750UP questions/suggestions

Re: Station bridge - abnormal traffic and NV2 ctrl.frame tim

Re: NV2 Timing related disconnects

Re: NV2 Timing related disconnects

Re: Station bridge - abnormal traffic and NV2 ctrl.frame tim

Re: Station bridge - abnormal traffic and NV2 ctrl.frame tim

Station bridge - abnormal traffic and NV2 ctrl.frame timeout

Re: New wireless protocol: Nv2 in v5.0beta5

Re: New wireless protocol: Nv2 in v5.0beta5

Re: New wireless protocol: Nv2 in v5.0beta5