+1 here!

Any updates on this?

NetBox for example: https://routerboard.com/RB911G-5HPacD-NB Is there any plan MikroTik build a RouterBOARD with the features below; -Minimum three Ethernet interfaces. -One PoE-in and two PoE-out "Active/Passive." -Dual-band wireless "2.4GHz and/or 5GHz." -mini-PCI express for ...

*) ppp - added output values for "info" command for finding the GSM base station's location ("LAC" and "IMSI");
Is there any documents available for this?

Do You mean LAC functionality is working? ie I can authenticate as an L2TP client to a Cisco server (LNS) What version is this working on? Great news if it is working ;-) Barry Yes, it is working. You could use " 6.35rc12 (Release candidate) " version of RouterOS. check the change-log. I ...

Any sign of this feature???

I'm down to last two ciscos, I'd hate to have to start the count increasing again...

It is working now! time to move from Cisco to MikroTik.

1: Upgrade your RouterOS to " 6.35rc11 (2016-Feb-17 09:09) " *) l2tp - added support for max-sessions; *) l2tp - added support for proxy authentication when receiving forwarded PPPoE sesssions; *) l2tp - added support for Hidden AVP, it is needed for proxy authentication; 2: Enable L2TP Se...

Hello, LNS protocol works on MikroTik RouterOS very stable faster and more reliable than Cisco Routers now! The previous major issue within MikroTik RouterOS was for "AVP" authentication protocol which MikroTik doesn't supported and the broblem caused by that issue: -There are two kind of ...

http://www.mikrotikcanada.ca Router#show run Building configuration... Current configuration : 3833 bytes ! ! Last configuration change at 20:31:58 EST Fri Dec 31 1999 ! upgrade fpd auto version 15.0 service timestamps debug datetime msec service timestamps log datetime msec no service password-encr...

什么是最好的信号强度和信号随机过程e on p2p and p2mp wireless link ?

I check my card and N-type and Antenna ... I change first all pigtail because of rainy day ... second change my card ... 3 ; routerboard .... but my problem is not solve ... today I change my antenna and change the antenna hight ( from 31m to 21m ) and I connect 2 antenna ( h&v ) and change my m...

I have a Wireless link with RB411AH+R52HN+ 1-30dBi MikroTik Dish antenna foe each side . for R52HN connect two MMCX pigtail that I only use one of them . ccq >99% signal=-51 for 11 Km and NV2 + btest > 112mbps for send and >102mbps for re My problem is : After 3~5 week my link is down My scan list i...

Now I have on Btest (Bouth S/R) 87 Mbps for send and 85Mbps on receive , with RB433AH and R52Hn , Dish antenna 30dBi
Thank you for your help.

My problem about (drop my ping ) is solved. I change my configuration from ; station side : Bridge : rstp port : ether1 , wlan1 Wireless: mode : Station-WDS , band 5GHZ-Onlyn , WDS-mode:dynamic , wds-d-b:bridge1 , wireless-protocol:any HT:any-above control , chain0 , chain1 AP Side : bridge : rstp P...

Thank you very much
I check this way .

Thank you for you help ,
Oh I don`t check for any dhcp server ...
Thank you again ...
Can I e-mail you my conf picture and support.rif if my problem is not solved?

Um.. and the another ... this link and the same link with 6 km distance is work about 14 days with this configuration ... and my problem is start today ... my costumers said to me the power is turn off and turn on again and the problem is start ....
all routerboard is connect to online UPS

OK , you think my problem only about my ip configuration ?
I delete all my ip address on my routerboards .... then when the poe cable connect to my computer I can ping the computer on siteB then when the POE cable connect to switch I can not ping the siteB computer

now ,!? i have another problem ... ???!!! some time when i connect to siteB (bridge mode) with WDS configuration , with MAC telnet on siteB routerbourd ... I don`t see the (DAC)wds interface under WLAN1 interface . and when deleting the bridge interface and rebuild the bridge interface and ports (et...

the first configuration on my router is : site A : Mode : bridge band : 5ghz-onlyN (20) freq(5700) superch scanlist:5700 NV2 nstream — wds-mode : dynamic wds-d-b:bridge1 — HT : any - above control - chain 0 , 1 - 0 site B : mode: station-WDS band 5ghz-onlyN freq : 5700 super scanlist: 5700 any —— wd...

I Set all ip address on Bridge interface

I change my ip address , the local subnet is 10.78.91.0/24 with no route to 192.168.88.1,2/24 this is my structure in siteA : 1:My laptop(ip address is 192.168.88.1) 2 : RB450 (Bridge all port with RSTP and ip:192.168.88.254) 3: RB433AH+R52Hn+30dBiANT IP address is 192.168.88.2 in siteB : 1: laptop ...

Hello , I`m sorry about my English . I have install one wireless link with : RB433AH , R52Hn , 2*MikroTik Dish antenna 30dBi V&H for about 14Km My routerOS version is 5rc1 I have 159mbps BW for send and 162mbps for receive and 87mbps(S)/77mbps(R) in btest ping time is ok , i don`t have any time ...

Hello, Happy new year (norouz) . about wireless link 802.11n !? for about 3 meter , routerboard 411AH , R52N , 16dBi dual Polar antenna , with eoip bridge ; test with btest on wlan we have about 222Mbps RX or TX and TX:103Mbps and RX:85Mbps ; and test with btest on ethernet 95.5Mbps for about 2.001 ...

Hello Normis . I test 4 link with 802.11n , with RB/600A ,R52N , 30dBi parabolic . On all of them when run BTest , the bandwidth are 115~149 Mbps depend on distance , but this is not my problem . when I send file from windows computer to another windows computer the traffic rate in WLAN interface sh...

1 : Station (RB/600A , R52n) mode : Station WDS band : 5ghz only N Freq : 5220 ssid : MikroTik Country : Denmark WDS : Dynamic , Bridge1 Nstreme : Enable HT : ChainTX,RX 1,2 AMPDU : 1 any above control 2 : AP ( RB/600A , 2* R52N) 2-1 : mode : Bridge band : 5Ghz only N Freq : 5220 SSID: MikroTik coun...

test with bandwidth test tools about 30 min

Site A : Latitude 36.065683° longitude 59.644694° Antenna Haight :60m Site B : Latitude 36.359510° longitude 59.540805° Antenna Haight :27m You can see our cctv camera and resemblance it in google earth (site A) if you whant . Please enable ALL activex in internet explorer ip address :89.165.40.217 ...

http://www.netware.ir This is a good solution for MikroPoint Antenna BEEP SCRIPT :local beep "10ms"; :local no "2400ms"; :local s90 "1290ms"; :local s85 "790ms"; :local s80 "590ms"; :local s77 "390ms"; :local s74 "290ms"; :local ...