Make sure you netinstall it with v7.3 which just came out. A reboot loop issue has been solved there.

Could you describe the process please? The device is mounted, outside on a mast and it is a big job getting it down to put it in netinstall mode.

If you try to upgrade router "in a normal way" (either by hitting the upgrade button or by uploading newer npk files), then there will be something in log to indicate why upgrade failed.

If the device doesn't boot how do I "see" the logs?!

on Sunday I cleared the configuration to default and then tried an upgrade via System>Packages, but still won't boot. I have also tried installing v7 via netinstall and that won't work either! People have showed me the RBLHGGR running v7 software, just can't figure out why mine refuses to work!

Hi, I have been trying to upgrade my RBLHGGR to ROS v7 but it refuses to boot! I have tried to upgrade via System>Packages and also netinstall but no matter what I try it leaves the device un-bootable. I just spent Sunday afternoon trying to get the device back on-line after trying to install ROS 7....

3UK Technical Support are about as useful as an ashtray on a motorbike. The only fix for questions is "turn it off, wait a few seconds and turn it back on again". They have absolutely no understanding of the network or even the current status (They have argued that the network is up and ru...

Anyone know when RBLHGGR will be supported? Every-time I have tried to test it, unit fails to boot and have to reset it with v6 software.

If I change the band by enabling only B20, I can connect to cell 1720070 which is on the same mast. But I can't connect to both (B3+B20) at the same time!

I installed one of your scripts to add these entries into my log, these are the changing value as I was running the command 20+ times. DIAG__LTE6: lte1: rcvd +EEMLTEINTRA: 0, 351, 1392, 36, 0 DIAG__LTE6: lte1: rcvd +EEMLTEINTRA: 0, 9, 1392, 32, 0 DIAG__LTE6: lte1: rcvd +EEMLTEINTRA: 0, 93, 1392, 33,...

I use Linux and can't get the information you are looking for. What is the difference between cell id and physical cell? In the cell monitor I am seeing lots of different PHY cell ids appearing on earfcn: 1392 and in the LTE info page can see I'm connected on 99. Cell monitor shows me numbers betwee...

/interface lte at-chat 0 input="at+eemginfo\?" output: +EEMLTESVC: 564, 2, 32, 3831, 99, 1392, 19392, 3, 15, 43, 16, 1, 2, 10, 0, 1, 0, 33000, 11, 3237756295, 1720064, 255, 0, 3, 44, 39, 18, 19, 61, 6, 112, 2, 2, 2, 2, 0, 0, 3, 22480, 2, 6, 6, 2, 11, 4, 33774, 10, 2, 83, 0 +EEMLTEINTERRAT:...

Still generic story. Remember that math: enB ID * 256 + Sector ID = Current Cell ID eNB ID - ID of your Tower for your ISP (other ISP at the same tower and antennas have other eNB ID) Sector ID - is a ID of sector antenna for specific band, like eg. id 0,1,2,3 can be 4 sides of the world for Band20...

I've found some of our local masts incorrectly marked. The one my SXT connects to is correct I think, Google Maps satellite images show two masts at the location, one of which is the one I connect to. My colleague has found the same, he connects to a mast that is not only in the wrong place on Cell...

Just an update. I finally found this rogue mast but it turns out that it's location was just an "estimate" based on user submitted signal recordings, so was sending me looking in the wrong direction!! I looked for the bright patches on the coverage checker and drove around in that area whi...

I was getting a good speed from the rogue cell and know it's ID, but I can't find it via the MikroTik dish, only B20! The only problem with this cell is that it kept throwing me off any time the local power went off and I couldn't get back onto it, without calling Three and getting them to "res...

对不起我的朋友,这道菜是在无线电塔!MikroTik_Mast.png It is times like this I regret selling the antenna rotator that used to be on the top of it. I have been out driving with CellMapper today trying to locate the mast's I am connecting to, but can't seem to locate the mast the "r...

Oh that is odd!! For B20 it's connecting to a base I know about which is 4.7km away, however for B3 it's connecting to "something" closer with a different eNB, but I can't find it's location. I been trying to collect points with cellmapper, but can't pinpoint it's location :/ The B3 signal...

Hi,

Sorry for interrupting on this thread, but I am looking to do the same thing as the OP. As with the OP I can connect to Band 3 or Band 20, but not both at the same time. Has anyone got this to work with Three UK?